Category Archives: Impreza

Log Graphs 1

Specification

Car: 2009 Impreza 2.0 Turbo Diesel, 110 kW / 148 hp / 150 PS, European domestic market, Euro 4 spec.

Important: Newer Boxer Diesel generations (Euro 5/6) may show different behaviour!

ECU firmware: patched ROM for unlimited logging, otherwise stock.
Protocol: SSM2 via CAN
More than 120 items had been logged, plenty of RAM variables (*) plus standard SSM2 items at roughly 170 ms interval.

Graphs

I prepared two graph images plotting some interesting parameters, click picture for full resolution:


Image 1/2

loggraphs1_p1


Image 2/2

loggraphs1_p2

Additional details

… at specific time positions:

#1: State before active regeneration

Time @ ~ 33 ½ min
Cruise Control: active
Vehicle Speed*: 110 km/h
Engine Speed: 2300 rpm
Gear: 5
Coolant Temperature: 93 °C
Injections: 2 (pre + main)
Soot Accumulation Ratio: 64 %
DPF Pressure Difference: ~ 5 kPa
Exhaust Gas Temperature (EGT) Catalyst Inlet: 345 °C
EGT DPF Inlet: 370 °C
Intake Air Amount: 430 mg/cyl
Mass Air Flow: 33.8 g/s
Manifold Absolute Pressure (MAP)*: 126 kPa
Inlet Air Temperature: 25 °C
Manifold Air Temperature: 48 °C
Fuel Temperature: 58 °C
Throttle Opening Angle: 79 deg
EGR Valve Opening Angle: 38 deg
Final Oil Dilution Rate*: -1.9 mg/s (evaporation)
Oil Dilution Amount: 282.0 g (4.6 %)

#2: Soot 65%, preparing for DPF regeneration

@ 33 ¾ min
Soot Accumulation Ratio* reaches 65%, this triggers active regeneration preparations. Note: I am referring to the actual RAM value, diagnostic parameter may indicate 65% earlier due to rounding.
Apparently ECU now does 3 injections (pre + main + after) when power demand is high enough, no post injections yet

#3: Active Regen ON

@ 34:04; = 20 seconds after #2, DPF Regeneration Switch turns ON
EGR valve closes instantly, 0 deg
Manifold Air Temperature dropping
Boost Control opens VGT immediately, from 52 to 25%
Manifold Absolute Pressure* dropping
pilot-injection kicks in, 2 injections (pilot C + main)
post-injections begin to fade in but not active yet

#4: Post-Injections

@ 33 seconds after #2, post-injections A + B become operational (injection amount > 0)
oil dilution rising
EGTs climbing
Manifold Absolute Pressure*: 75 kPa (~ 25 below ambient), varying, stays below ambient most of the time during regen at low power demand
EGT Catalyst Inlet: 340 °C
EGT DPF Inlet: 320 °C
injections: 4 (pilot C + main + post A + post B)

#5: Coasting Fuel Cut-Off During Regen

Example @ 35:12
EGR valve opens instantaneously, 70 deg; EGR behaves rather digitally during regen – either fully closed (0 deg, for max EGT) or max opened (70 deg, less fresh air)
Throttle Opening Angle: rising up to 31 deg
injections: 0
Fuel Consumption*: 0 mm³/s
oil dilution going down slowly due to estimated evaporation
EGT Catalyst Inlet: decreases fast, EGT at DPF inlet (> 600 °C) follows with a delay
Engine Speed: gear change from 5th to 6th to reduce engine braking effect

#6: Idling with Active Regen ON

@ 45:30
Engine Speed: 800 rpm
Post A Injection Amount*: 0
Post B Injection Amount*: ~ 8 mm³/st
Apparently while idling the ECU prefers the 2nd post-injection (“B”), otherwise during driving it’s rather mixed
Final Oil Dilution Rate: ~ 20 mg/s (medium)
Boost Control: 25 % (VGT fully open)
Manifold Absolute Pressure*: 74 kPa
Throttle Opening Angle: 5.5 deg
EGR Valve Opening Angle: 0 deg
Intake Air Amount: 370 mg/cyl
Mass Air Flow: 9.8 g/s

#7: DPF Regeneration OFF

@ 46:15, decision is based on elapsed time from #2, achieved soot level does not matter (!)
DPF Regeneration SW had been ON for 12.2 minutes
all post-injections off
Oil Dilution Amount*: 299.6 g (4.9 %) = + 0.3 % during regeneration
EGR back to normal operation
Boost Control: 65 % instantly (max speed, spooling up turbo)
MAP rising
EGT Catalyst Inlet: 270 °C
EGT DPF Inlet: 490 °C